GPS Aquameter – Handheld device with built in GPS data tagging

The GPS Aquameter is the original handheld water quality meter with built in GPS. The built in GPS receiver allows the meter to record the location of every dataset, meaning you will always know where your data was captured. The meter is designed to be picked up and used by anyone intuitively. It requires no boot up or warm up time and allows you to record data with a single button press.


The GPS Aquameter

GPS Aquameter Provides Pin Points in Google Earth and is extremely easy to use

GPS Aquameter features

  • Built in GPS receiver to enable location tagging with every data set, view data in Google Earth
  • Display of all the parameters being measured; scroll left and right to view
  • Record your data set at the touch of a single button, press M+ to record full data set including all parameters, GPS data and calibration data
  • New low power auto data logging mode allows automatic data capture for up to 38 days
  • Built in air pressure sensor for atmospheric compensation
  • Ergonomic curved design sits nice in the hand, with rubber gasket for added grip in wet conditions
  • Rugged, metal AquaConn connectors provide extreme durability where its needed most
  • AquaLink PC application and USB cable provided with every GPS Aquameter for data management

View your water quality data in real time with the GPS Aquameter

Even if you will be using your Aquaprobe with an AquaLogger or other device, you will still need a GPS Aquameter. The meter gives you real time readings via the display, which are useful when deploying your logging system as it allows you to check the parameters are all reading ok.

GPS meter or Aquaprobe PC-KIT required for probe calibration

More importantly you will need an Aquameter or the Aquprobe PC-KIT to perform calibrations on all of the probe’s sensors. If you are purchasing multiple probes for unmanned logging, then you will only need to purchase either 1 meter or 1 PC-KIT.

GPS Aquameter Full Specification

Screen Shot 2015-07-24 at 11.10.47

Aqualogger – Unmanned logging devices for medium term deployment

The AquaLogger is a rugged data logger designed for short – medium periods of unmanned monitoring. It features a large 15,000 data set memory, houses a pressure sensor for barometric pressure measurement and it is powered by standard C cell batteries.  There are 2 versions available, depending on the Aquaprobe you are using.

The AquaLogger-7000

Leave your AquaLogger anywhere

The AquaLogger is designed to be left in the field for long periods of time. It’s rated to IP-67 and contains an air pressure sensor to allow all the automatic compensation to take place.

Easy set up and deployment

It couldn’t be easier to set up thanks to the easy to use LoggerLink. On the left of the screen are the existing settings, currently held by the logger, and on the other side are the new settings options. Once you have updated the new settings all you have to do is press upload and its ready for deployment! It will even tell you how much logging time you have left, in days, based on the settings you have chosen!

AquaLogger Full Specifications

Screen Shot 2015-07-24 at 11.21.17

AquaLogger Battery Life Guide

AquaLogger battery life

Please Note:

  1. When cold, alkaline batteries will not perform to their full specification. For this reason, the battery life estimations shown above and in the LoggerLink Software will be significantly shorter (by up to 50%) at lower temperatures.
  2. When the battery voltage becomes low, the cleaning function will be suspended (AP-7000 only).


BlackBox – SDI-12 or Modbus RS485 data converter

The BlackBox is a data converter that allows any model of Aquaread water quality probe to be interfaced directly to a third party processing, control or logging device. With a choice of industry standard digital interfaces the BlackBox offers a versatile and cost effective data conversion solution.

The BlackBox

BlackBox features

  • Compatible with all Aquaprobes and AquaPlus probes
  • Integral barometric pressure sensor for depth and DO correction
  • Able to output data from any Aquaread water monitoring sensor; standard, optical or ISE types
  • SDI-12 Digital interface
  • Modbus (RS485) Digital Interface
  • Wide operating voltage range
  • Rugged construction with strong fixing flange
  • LED status indicator
  • IP67 rated
  • Suitable for long term unmanned deployment

BlackBox Specifications

Screen Shot 2015-07-24 at 11.45.31

Telemetry Frog RX GSM Telemetry Device

The Frog RX Telemetry Device

Frog RX features

  • Ultra-low power battery operated for remote, harsh environments
  • Can be used with all Aquaprobes via a BlackBox
  • Can be used with all LeveLine water level and temperature loggers
  • SDI-12 Digital interface
  • Internal breather-bag allows venting for gauge pressure sensors
  • Field replaceable batteries
  • Uses Harvest software to set up the logger prior to deployment
  • Uses Timeview to display data and communicate with the logger

TimeView Online Platform

Bodenham TV Alarm 1

  • View your data online from any device with internet access
  • Set up alarm triggers to send out email and optional SMS messages to key personnel
  • Combined with the Harvest software you can update settings on your PC and upload them to the Frog at its next dial in
  • Export your data as a .csv file for data manipulation and storage

AquaCal – Aquaprobe Live Data & Calibration Utility

The AquaCal windows PC software

Download AquaCal Here

Use the Aquaprobe PC-KIT including the AquaCal software to allow you to connect your Aquaprobe directly to a PC via USB

The AquaCal Gallery

AquaCal Features

  • Allows you to connect your Aquaprobe to a PC using the adaptor kit
  • View live readings from the Aquaprobe on your PC
  • Log data from the Aquaprobe on your PC
  • Fully calibrate your Aquaprobe without the need for an Aquameter
  • Produce calibration reports after calibration